Search found 92 matches

by Ghost
Mon Nov 06, 2023 4:46 pm
Forum: Drivetrain - Motors, Turbos etc..
Topic: Gearbox Bellhousings
Replies: 2
Views: 2143

Re: Gearbox Bellhousings

Did you have any luck?
I have no idea, seems everyone has run away to Facebook groups now :axe:
by Ghost
Wed Jan 18, 2017 2:32 pm
Forum: General Tech
Topic: N/A Piazza workshop manual? & Fuel question.
Replies: 4
Views: 9695

Im surprised how much that car went for considering it was basically in the middle of nowhere (I was going to bid $700 and pay $850 for shipping..) How bad was the rust IRL, the photos were not too clear.. No idea on the specs however I would imagine it would be about the same as a SOHC engine, I do...
by Ghost
Sat Aug 08, 2015 3:21 pm
Forum: News
Topic: Oil sniffing - Opie Oils
Replies: 8
Views: 9815

Nothing in my inbox
by Ghost
Tue May 05, 2015 6:51 pm
Forum: Media Gallery
Topic: 1981 Piazza Commercial
Replies: 3
Views: 8587

53KM/h!!!!!
That ad is all over the place
by Ghost
Mon Oct 13, 2014 4:37 pm
Forum: Small Talk
Topic: Ghost Piazza Build
Replies: 4
Views: 6365

The rust actually looks worse in the photos than it does IRL.
I sandblasted the rear last summer, its already getting a layer of surface rust on it because of my slowness..
by Ghost
Sat Oct 11, 2014 6:32 pm
Forum: Small Talk
Topic: Ghost Piazza Build
Replies: 4
Views: 6365

by Ghost
Mon Oct 06, 2014 6:44 pm
Forum: Small Talk
Topic: Ghost Piazza Build
Replies: 4
Views: 6365

Ghost Piazza Build

Thought I would make a build thread for my drawn out project to get some more motivation. It started out like this, looks good on the surface, however rust lurks just below the surface: http://e4675d6c-a-62cb3a1a-s-sites.googlegroups.com/site/aucklandweb/piazza/Piazza800x600.jpg It is now sitting in...
by Ghost
Sun Aug 03, 2014 10:44 am
Forum: Suspension, Wheels and Tires
Topic: Bilsteins
Replies: 6
Views: 7526

Are they really much better than KYB Shocks?
They seem to be pretty expensive.
by Ghost
Sat Sep 07, 2013 9:10 am
Forum: General Tech
Topic: Noise, what is it?
Replies: 10
Views: 13224

IZU069 wrote:If it's also quiet in 4th gear but not others, then it's the mainshaft's center bearing - a needle bearing with worn inner & outer shaft surfaces.
Sounds like the same issue my friends gearbox was having, I think thats the same conclusion we came to as well.
by Ghost
Thu Aug 15, 2013 4:38 pm
Forum: AU & NZ - Wreckers that have Piazzas
Topic: The more info you can post up the better, get pics.
Replies: 6
Views: 9440

It will be long gone by now.
Then again one of my local car crushers saved quite a few cars from destruction, probably why they lost 50m last year and went broke..
by Ghost
Wed Aug 07, 2013 6:53 pm
Forum: Audio and Electronics
Topic: My first digidash fix. (FIGJAM!)
Replies: 9
Views: 9255

Wonder how well a 7" tablet screen will squeeze between the speedo and rev counter.
I should go and measure the one out of my wreck.
by Ghost
Tue Aug 06, 2013 4:03 pm
Forum: Audio and Electronics
Topic: My first digidash fix. (FIGJAM!)
Replies: 9
Views: 9255

Always wanted a DigiDash in mine, but I think if I were to get one now I would make one from scratch, and it would be a digital mechanical hybrid.
Just need to get around to learning some basic programming to control an ARM board and decide what I can actually display on it.
by Ghost
Sat Jul 20, 2013 9:45 am
Forum: Articles
Topic: Low Rider
Replies: 3
Views: 12343

May 2000.
Car is probably dead now.

Does look like a lot of work went into it though.
by Ghost
Sat May 11, 2013 7:41 pm
Forum: General Tech
Topic: Australian VIN identification
Replies: 9
Views: 11269

There is an important delineation requred here, there are mechanics and fitters. These days most spanner men are fitters and don't have many spanners, they do have laptops and OBD readers. The amount of times I have heard that in the last 12 months... My family has a truck/quarry business and they ...