Search found 783 matches
- Mon Jan 07, 2013 2:37 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: MUA-5 Transmission Swap.
- Replies: 66
- Views: 89833
Yeah Australian Piazzas are hydraulic, not sure when Japan changed over but i've seen photos of G200 Piazzas with cables. However US G200Z impulses were hydraulic. I assume this is because the clutch pedal is in the right place to mount the master cylinder on LHD models. Then they later figured out ...
- Sun Jan 06, 2013 10:18 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: MUA-5 Transmission Swap.
- Replies: 66
- Views: 89833
- Sat Jan 05, 2013 9:04 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: MUA-5 Transmission Swap.
- Replies: 66
- Views: 89833
This is the dash and centre console mounting bracket, it needs the lower mounting holes moved further up, either by cutting the bottom of it then flattening the bottom edges of those holes in the middle of it and redrilling the mounting holes, or by cut and shut welding. http://starlyon.com/bugle/pi...
- Fri Jan 04, 2013 11:39 am
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: MUA-5 Transmission Swap.
- Replies: 66
- Views: 89833
- Thu Jan 03, 2013 10:04 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: MUA-5 Transmission Swap.
- Replies: 66
- Views: 89833
I beat up my tunnel a bit, seems the tunnel goes high then slopes down slighty as it goes toward the firewall, so I had to beat it up at the front to make it more horizontal where the shifter goes. Making the clearance on the left side was easy enough. This creates 2 problems above. There's a mount ...
- Fri Dec 28, 2012 11:30 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: Need Help sorting out cooling system.
- Replies: 10
- Views: 11367
Found someone who made a turbo oil feed off that hole on a G series engine and they say it's 1/8" BSP so it's likely to be the same on a 4Z.
http://www.ozgemini.com/forums/tech/vie ... 930#172930
http://www.ozgemini.com/forums/tech/vie ... 930#172930
- Fri Dec 28, 2012 11:26 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: Need Help sorting out cooling system.
- Replies: 10
- Views: 11367
- Fri Dec 28, 2012 5:20 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: Need Help sorting out cooling system.
- Replies: 10
- Views: 11367
On mine there's a water gallery running through the manifold from the thermostat to between cyls 3/4 where a pipe exits the bottom and that is then hooked up to the pipe that runs across the back of the engine, so aslong as it comes out of the inlet manifold side of the thermostat it'll do. There's ...
- Wed Dec 26, 2012 10:14 am
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: Need Help sorting out cooling system.
- Replies: 10
- Views: 11367
There's a pipe that bolts to two of the top bellhousing bolts and goes from under the intake manifold across to the other side of the engine. Then that pipe along with the one in the picture going to the back of the block are connected to the heater core. The two pipes also have a small heater core ...
- Fri Dec 07, 2012 10:22 am
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: MUA-5 Transmission Swap.
- Replies: 66
- Views: 89833
- Wed Nov 07, 2012 11:24 am
- Forum: Show room
- Topic: My black forged Piazza
- Replies: 137
- Views: 104271
The rattles are normal, read a review of the Piazza when they were new! Mine had dash squeaks going over bumps. Rear end might be suspension bushes, are they ok? The lower arm to body bush broke on one side of mine sending the arm off to the side to rub on the arm mount. The R12 replacement is calle...
- Mon Oct 29, 2012 8:05 pm
- Forum: Show room
- Topic: My black forged Piazza
- Replies: 137
- Views: 104271
- Sat Oct 27, 2012 8:42 pm
- Forum: Show room
- Topic: My black forged Piazza
- Replies: 137
- Views: 104271
Yeah the problem was you got the relay out of another Piazza! They always get smashed by the battery because hardly anyone with a Piazza believes in Newton's laws of motion. Fix the coolant thing? The sensor is in the overflow bottle, so the radiator can be full but it requires the overflow bottle t...
- Mon Oct 15, 2012 11:17 pm
- Forum: Drivetrain - Motors, Turbos etc..
- Topic: MUA-5 Transmission Swap.
- Replies: 66
- Views: 89833
I have been hacking away at my alloy housing to build my own shifter assembly, but I am stuck with getting that linkage arm/ball off the shaft. I could use a little advice in that area... It has a roll pin inside a roll pin to lock it onto the shaft, you'll need to make a punch for each size, or ma...
- Mon Oct 08, 2012 7:14 pm
- Forum: Suspension, Wheels and Tires
- Topic: Custom springs
- Replies: 24
- Views: 25554